[ Pobierz całość w formacie PDF ]
Z
BODY COMPONENTS 23 - 1
BODY COMPONENTS
CONTENTS
page
page
DOORS ...............................
EXTERIOR COMPONENTS .................
FIXED WINDOW GLASS ..................
INTERIOR COMPONENTS .................
PAINT CODE CHART .....................
POWER SUNROOF ......................
REFINISHING PROCEDURES ..............
UNDERBODY COMPONENTS ..............
EXTERIOR COMPONENTS
INDEX
page
page
Battery Tray .............................
Body Side Cladding .......................
Body Stripes/Decals .......................
Cowl Grille and Screen ....................
Exterior Nameplates ......................
External Mirrors ........................
Front Fender ............................
Grille and Grille Opening Reinforcement (GOR) . . .
Hood ..................................
Hood Adjustment .........................
Hood Hinges ............................
Hood Latch .............................
Hood Latch Striker ........................
Latch Release Cable ......................
Luggage Rack .........................
Quarter Window Applique/Air Exhauster .......
Radiator Support Crossmember ...............
Safety Latch Striker .......................
Woodgrain (Vinyl Clad Metal) Molding ..........
Woodgrain Overlay .......................
GRILLE AND GRILLE OPENING REINFORCEMENT
(GOR)
(3) Grasp upper edge of headlamp lens. Pull
straight back (away) from grille opening reinforce-
ment (GOR). Disengage upper adjuster pivot from
lens assembly.
REMOVAL
(1) Remove 3 screws and grille (Fig. 1) from grille
opening reinforcement (GOR).
Fig. 1 Grille Removal
(2) Grasp lower edge of headlamp lens. Pull
straight back (away) from grille opening reinforce-
ment (GOR). Disengage lower adjuster pivots from
lens assembly (Fig. 2).
Fig. 2 Headlamp Removal
 23 - 2 BODY COMPONENTS
Z
(4) Locate and disconnect the 3 wire connector be-
hind headlamp.
(5) Rotate bulb ring counterclockwise. Remove ring
and bulb from lens (Fig. 3).
(10) Twist lamp socket clockwise. Disconnect lamp
socket from lamp.
(11) Remove upper screws at turn signal lens. Pull
lens out to access lamp sockets (Fig. 5).
(12) Remove turn signal and side marker lamp
sockets by twisting sockets clockwise.
(13) Remove lens.
Fig. 3 Headlamp Bulb Removal
(6) Open hood.
(7) Remove side marker lamp upper screw located
below radiator side closure panel (Fig. 4).
Fig. 5 Turn Signal Lens
(14) Repeat procedure for other side of front end.
(15) Remove license plate bracket if equipped, from
bumper fascia/crossmember.
(16) Remove 6 retainers at front fascia (Fig. 6).
Fig. 6 Lower Fascia Removal
Fig. 4 Side Marker Lamp Removal
(17) Remove 3 plastic rivets at each front wheel
well (Fig. 7).
(18) Slide fascia off retainer pegs at side of lower
crossmember.
(8) Remove lower screw located above park/turn
signal lamp.
(9) Pull out lamp.
Z
BODY COMPONENTS
23 - 3
Fig. 7 Wheel Well Retainers
Fig. 9 GOR Air Seals
(19) Remove fascia from lower crossmember (Fig.
6).
(20) Remove 8 bolts that attach grille opening rein-
forcement (GOR) to the upper and lower crossmember
(Fig. 8).
Fig. 8 Grille Opening Reinforcement
Fig. 10 Underhood Lamp
(21) Remove grille opening reinforcement.
(22) If necessary, remove air seals located at head-
lamp wiring inlets (Fig. 9).
(3) Mark location of the hood hinges and hinge
shims (Fig. 11) for installation alignment.
(4) Remove nuts that attach hinges to hood. Re-
move hood from vehicle with aid of a helper.
INSTALLATION
For installation, reverse removal procedure.
INSTALLATION
(1) Position hood on shims and hinges. Finger-
tighten hinge nuts (Fig. 12).
(2) Align hinges and shims (Fig. 11) with installa-
tion reference marks. Tighten hinge nuts to 23 N
RADIATOR SUPPORT CROSSMEMBER
Refer to Group 7, Cooling Systems for service infor-
mation.
m
(17 ft-lbs) torque.
(3) Test latch release cable and latches for proper
operation.
(4) Connect underhood lamp wire harness connec-
tor (Fig. 10).
(5) Inspect hood for proper alignment and adjust as
necessary.
HOOD
REMOVAL
(1) Raise hood.
(2) Disconnect underhood lamp wire harness con-
nector (Fig. 10), if equipped.
I
 23 - 4 BODY COMPONENTS
Z
Fig. 11 Hood Hinge
Fig. 13 Hood Bumper
Fig. 12 Hood Hinges and Release Cable
Fig. 14 Hood Latch
HOOD ADJUSTMENT
The hood attaching holes are enlarged to aid front,
back and side-to-side adjustment.
(1) If hood is low in relation to cowl panel, insert
shims between hinge and hood.
(2) Adjust hood bumper (Fig. 13) in or out to adjust
hood-to-fender height alignment.
(3) Adjust the hood latch (Fig. 14) as necessary.
Tighten the nuts to 11 N
(4) Align latch striker (Fig. 12) so that striker en-
ters the latch squarely and without binding.
HOOD HINGES
m (8 ft-lbs) torque after
REMOVAL
(1) Remove hood from vehicle.
(2) Remove hinge retaining nuts from studs (Fig.
11).
(3) Remove hinge from inner cowl side panel.
adjustment.
I
 Z
BODY COMPONENTS 23 - 5
INSTALLATION
(1) Position hinge over studs (Fig. 11).
(2) Install hinge retaining nuts on studs. Tighten
retaining nuts to 23 N
I
m (17 ft-lbs) torque.
(3) Install hood.
(4) Adjust hood as necessary. If necessary, refer to
adjustment procedure.
HOOD LATCH
REMOVAL
(1) Remove nuts that attach latch to radiator
crossmember support (Fig. 12).
(2) Disconnect latch from the hood release cable.
Remove latch.
INSTALLATION
(1) Connect latch to latch release cable. Position it
on radiator crossmember support (Fig. 12).
(2) Install nuts.
(3) Tighten nuts to 11 N
m (8 ft-lbs) torque.
(4) Test operation of latch release cable and latch.
I
Fig. 15 Hood Release Cable
HOOD LATCH STRIKER
SAFETY LATCH STRIKER
REMOVAL
(1) Remove 2 striker retaining bolts.
(2) Remove striker from hood (Fig. 12).
REMOVAL
(1) Remove latch striker screw from hood (Fig. 12).
(2) Remove striker from hood (Fig. 12).
m (8 ft-lbs) torque.
(3) Test striker/hood alignment by opening and
closing hood several times. Adjust striker, if neces-
sary.
I
INSTALLATION
(1) Position striker on hood. Install screw (Fig. 12).
(2) Test safety latch operation.
COWL GRILLE AND SCREEN
LATCH RELEASE CABLE
REMOVAL
(1) Use a wax pencil to mark position of wiper
arms (Fig. 16).
REMOVAL
(1) Disconnect cable from hood latch (Fig. 14).
(2) Disconnect cable from retaining clips (Fig. 12).
(3) Remove left cowl side (kick) trim panel.
(4) Remove cable bracket attaching screws from
cowl side panel (Fig. 15).
(5) Pull cable through dash panel and remove it
from under instrument panel.
INSTALLATION
(1) Insert replacement cable end through hole in
dash panel (Fig. 15) into engine compartment.
(2) Pull cable forward and seat grommet in dash
panel (Fig. 15).
(3) Position cable bracket on cowl side panel and
install screws (Fig. 15). Tighten screws to 11 N
I
m(8
ft-lbs) torque.
(4) Install left cowl side trim panel.
(5) Route cable into retaining clips.
(6) Attach cable to hood latch (Fig. 12).
(7) Test release cable for proper operation.
Fig. 16 Wiper Locations On Windshield
(2) Remove windshield wiper arms from pivots
(Fig. 16).
INSTALLATION
(1) Position striker on hood. Install bolts (Fig. 12).
(2) Tighten bolts to 11 N
  [ Pobierz całość w formacie PDF ]