[ Pobierz całość w formacie PDF ]
Z
POWER MIRRORS 8T - 1
POWER MIRRORS
CONTENTS
page
page
AUTOMATIC DAY/NIGHT REAR VIEW MIRROR .
POWER SIDE MIRRORS ...................
POWER SIDE MIRRORS
INDEX
page
page
General Information .......................
Heated Mirror ...........................
Mirror Assembly Replacement ...............
Mirror Switch Replacement ...................
Mirror Switch Test Procedure .................
Mirror Test Procedure ......................
GENERAL INFORMATION
For information concerning wiring or connectors,
refer to Group 8W - Wiring Diagrams.
The mirror control switch uses a paddle which is
moved Left or Right for mirror selection and 4 but-
tons for mirror movement direction (Fig. 1).
Each mirror has two reversible motors: one to ad-
just the mirror view up and down, the other to adjust
the mirror view right and left. The driver operates
the switch that controls the polarity of the voltage to
the motors. The mirror select switch directs these
control voltages to either the RH or LH mirror.
The mirror select switch must be set to L or R to
direct current flow.
HEATED MIRROR
The heated mirror is controlled by the rear window
defogger switch. The mirror heater is on only when
the rear window defogger switch is on.
Refer to Group 8N - Rear Window Defogger.
MIRROR TEST PROCEDURE
CAUTION: The wiring harness to the door switches
is just long enough to allow installation. If trim panel
is pulled off by hand the switch may be pulled apart.
Use a door clip tool to prevent damaging the
switches.
(1) Remove the door trim panel with a wide flat
blade tool (Fig. 2).
To aid in removal of the trim panel, start at
the bottom of the panel.
(2) Unplug door wiring harness connector.
(3) Connect a jumper wire to a 12 volt source.
Fig. 1 Power Mirror Switch
(4) Connect another jumper wire to a good body
ground.
(5) Refer to Mirror Motor Test for appropriate pin
numbers (Fig. 3).
 8T - 2 POWER MIRRORS
Z
Fig. 2 Trim Panel Removal
Fig. 4 Mirror Switch Test
Fig. 3 Mirror Motor Test
MIRROR SWITCH TEST PROCEDURE
(1) Remove power mirror switch from mounting po-
sition.
(2) Unplug wiring harness connector.
(3) Using an ohmmeter, test for continuity between
the terminals of the switch as shown in the Mirror
Switch Test (Fig. 4).
MIRROR SWITCH REPLACEMENT
(1) Disconnect negative cable from the battery.
(2) Remove ash tray.
(3) Remove 6 screws holding center cluster bezel
(Fig. 5).
(4) Remove center bezel.
(5) Remove 2 screws holding dash pad located be-
hind top of center bezel.
(6) Gently pry defroster grille out of dash pad.
(7) Unplug sensors (if equipped) and set defroster
grille aside.
Fig. 5 Remove Center Bezel Screws
 Z
POWER MIRRORS 8T - 3
POWER MIRROR SCHEMATIC
8T - 4 POWER MIRRORS
Z
(8) Remove 4 screws in defroster duct opening hold-
ing dash pad (Fig. 6).
(13) With driver’s door open remove 1 screw from
the side of the lower trim panel (Fig. 9).
(14) Remove 1 screw from bottom of lower trim
panel and pull panel off. There is also a clip holding
the panel to the instrument panel.
(15) Remove 1 screw holding top of mirror switch
bezel (Fig. 10).
(16) Remove 1 screw holding bottom of bezel (Fig.
11). Remove the mirror switch bezel far enough to
unplug connector.
(17) Depress locking tabs and remove switch from
bezel (Fig. 12).
(18) To install the switch, reverse the removal pro-
Fig. 6 Upper Dash Pad Attaching Screws
(9) Remove 3 screws above Instrument Panel clus-
ter holding dash pad (Fig. 7).
Fig. 7 Remove Screws Holding Dash Pad
(10) Open glove box and remove 2 screws holding
dash pad.
(11) Remove dash pad pulling up to unsnap end
clips.
(12) Remove 4 screws holding the steering column
cover (Fig. 8).
Fig. 9 Lower Trim Panel
Fig. 8 Steering Column Cover
Fig. 10 Remove Screw Holding Top Of Bezel
cedures.
Z
POWER MIRRORS 8T - 5
To aid in removal of the trim panel, start at
the bottom of the panel.
(7) Unplug mirror wiring from door harness at con-
nector (Fig. 15).
(8) Remove 3 nuts holding mirror and remove mir-
ror.
(9) To install the mirror, reverse the removal proce-
dures.
Fig. 11 Remove Screw Holding Bottom Of Bezel
Fig. 13 Door Panel Removal
Fig. 14 Trim Panel Removal
Fig. 12 Power Mirror Switch Removal
MIRROR ASSEMBLY REPLACEMENT
(1) Remove screw at top of trim panel near mirror
(Fig. 13).
(2) Remove screw from demister opening.
(3) Remove screw and door handle cover.
(4) Remove screw from under armrest.
(5) Remove screw from bottom of hand hold in arm-
rest.
(6) Remove the trim panel with a wide flat blade
tool (Fig. 14).
Fig. 15 Power Mirror Removal/Installation
  [ Pobierz całość w formacie PDF ]